Reaction Torque Transducer

Static Reaction Torque Sensor and Reaction Torque Transducer FF410 Static Reaction Torque Transducer has been designed with nominal rated torque levels from 100 to 10,000 Nm. Using standard DIN flanges, this static transducer is made more efficient than other options available.

Reaction torque transducer. A Reaction Torque Sensor is a transducer that converts a torsional mechanical input into an electrical output signal. Transducer Techniques manufactures Reaction Torque Sensors in the capacity range of 5 in-oz to 100,000 in-lb. Honeywell reaction torque sensors utilize bonded, strain gauge technology and offer torque measurements from 25 oz-in (0,18 Nm) to ranges of 200000 ft-lb (271000 Nm) A variety of mounting configurations are offered including: Shaft to Shaft, Flange to Flange and Shaft to Flange on the low range models. A Torque Sensor is defined as a transducer used for torque measurement (torque sensing) that converts an input mechanical torque into an electrical output signal. Torque Sensors are also commonly known as Torque Transducer or Torque Cell. There are two main types of Torque Sensors: Reaction Torque Sensors or Rotary Torque Sensors. A torque sensor, is a transducer that converts a torsional mechanical input into an electrical output signal. A reaction torque sensor measures static torque, and rotary measures dynamic torque. Rotary torque transducers are used in applications where the torque transducer must rotate when attached to a spinning shaft. A rotary torque.

These Annular Transducers are designed to fit directly to the Norbar 92 and 119 diameter torque multipliers and will accurately measure the torque output from the gearbox, via a display instrument. Up to 5,000 N·m (5,000 lbf·ft) classified to BS7882:2017, typically better than Class 1 for the primary classification range (±0.5% of reading. FUTEK’s TFF400 Reaction Torque Sensor feature a Flange to Flange mounting solution with torque measurements ranging from +/- 5 inch-oz to 500 inch-pounds, (+/-0.04 to 60 Nm) and Torsional Stiffness of 325 inch-oz/radians to 199,000 Inch pounds/radians. Model 2110 Series Flanged Reaction Torque Sensor, 2,000 lb-in to 2,400,000 lb-in, 0.1 % Non-linearity and Hysteresis, High Torsional Stiffness, Higher Resistance to Bending Moments. Model 2110-2116 flanged reaction torque sensor is designed for installation between test pieces such as motors, switches, axles, or shafts and their mounting plate. A reaction torque transducer measures torque transferred to ground (or any rigid structural member). While intended primarily for static torque measurement, these reaction transducers can also measure dynamic torque, thanks to Newton’s third law of motion. (For every action there is an equal and opposite reaction.)

Shaft style reaction torque transducer mini torque sensor Features Stainless steel construction,miniature size Shaft to shaft type torque transducer Strain gauge technology,analog output Reaction torque. Read More. 2019-06-28 16:02:18. Dual flange reaction torque sensor torque measurement transducer. Flanged reaction torque sensors 225,97 Nm to 271K Nm capacities 0.1 % non-linearity & hysteresis Model QFFH-9 Flanged reaction torque sensors 3,000 in-lb to 24,000 in-lb maximum non-linearity of 0.1% Stainless steel Torque Transducers Provides excellent long-term stability and reliability using a highly accurate non-contact measuring technique. Special units made to customer requirements are available. Due to it’s compact design, the TB1A toque transducer is very well-suited for use in testing machines or as a reaction torque sensor. TN Non-rotating torque transducer specifically for use as a transfer standard or as a reference transducer in calibration laboratories.

Model 5330 reaction torque transducer features a large thru-hole design for use where mating fixtures, hydraulic or electrical lines need to pass through the sensor. See datasheet for available models, additional capacities, connectors, options, and accessories. The RTS series torque sensors were designed to fill the need for accurate reaction torque measurement below 62.5 in.lbs. capacity ranges 5 ounce inches through 1000 ounce inches. A torque sensor, torque transducer or torque meter is a device for measuring and recording the torque on a rotating system, such as an engine, crankshaft, gearbox, transmission, rotor, a bicycle crank or cap torque tester.Static torque is relatively easy to measure. Dynamic torque, on the other hand, is not easy to measure, since it generally requires transfer of some effect (electric. In addition, the drive shafts can lead axially through the torque sensor, thanks to the central bore. Due to itsthe compact design, the transducer is very well- suited for use in testing machines or as a reaction torque sensor with the direct coupling of the drive motor or transmission.

SENSY offers a complete range of static (‘non-rotating’) and rotating (dynamic) torque meters. The measurement ranges available for the first type range from 2 Nm to 1000 kN m. Depending on the capacity and the environment, our torque meters are available in the following materials: stainless steel, alloy steel, aluminum. As the standard, you will obviously find the ‘classic’ models. A torque sensor or torque transducer is a device for measuring and recording the torque on a rotating system. View products Show subnavigation ← Back to previous; Reaction Torque Sensors Torque Sensors Reaction Torque Sensors. Reaction torque sensors in different structural shapes for your needed application. View products FF410 Static Reaction Torque Transducer has been designed with nominal rated torque levels from 100 to 10,000 Nm. Using standard DIN flanges, this static transducer is made more efficient than other options available. Model 940 High Range Reaction Torque Watch Gaguge, 0.1 Nm to 1.4 Nm Accuracy: +/- 2%. Model: 940. Order Code: TQ9401, TQ9402 TQ9401M, TQ9402M TQ9401SI, TQ9402SI. Price: From Consult Factory Lead Time: From Consult Factory

Static torque sensors designed to measure reaction torque using bonded foil strain gages with excellent temperature stability and measurement ranges up to 8,000 lbf-ft. High level outputs available; Types of Torque Sensors. Automotive Torque Sensors. Contactless Torque Sensors.